How to Fix No Sound on a Sony STR-DH790

When a Sony STR-DH790 turns on but makes no sound, the cause is usually a setting, not a broken receiver: the wrong input, mute, the SPEAKERS button set to off, headphones in the PHONES jack, or an HDMI setting that sends the sound to your TV. Start with the quick checks below. For silent TV apps, press AMP MENU and make sure “<HDMI>” > “CTRL.HDMI” is set to “CTRL ON,” then select the receiver’s TV input.

If the quick checks don’t fix it, use the symptom table to jump to the right section. Silence from every source, from the TV only, from one device, or from one speaker each has its own causes. Everything here comes from Sony’s STR-DH790 Help Guide and support pages, put in the order that saves you the most time.

Quick checks (do these first)

  1. Check the input. Press the input button on the remote, or turn INPUT SELECTOR on the receiver, until the source you want shows on the display.
  2. Cancel mute. Press the muting button on the remote. MUTING disappears from the display when sound is back.
  3. Turn the volume up. Make sure MASTER VOLUME isn’t at VOL MIN. Turn up the volume on the playback device too.
  4. Switch the speakers on. Press SPEAKERS on the receiver until a setting other than OFF appears.
  5. Unplug headphones. Anything in the PHONES jack moves the sound to headphones.
  6. Check the power and cables. Make sure every connected device is turned on and every cable is pushed fully into its jack.
STR-DH790 front panel with INPUT SELECTOR, MASTER VOLUME, SPEAKERS and PHONES marked for quick checks
Generated illustrative recreation of the STR-DH790’s front controls. Check the selected input, raise the volume above VOL MIN, select speakers rather than OFF, and disconnect headphones. BD/DVD and VOL 25 are example display values.

If sound is back, you’re done. If not, find your symptom below.

Which kind of silence do you have?

What you noticeGo to
Nothing plays from any sourceNo sound from anything
Players and consoles work, but TV apps and channels are silentNo sound from the TV
One device is silent, the others workNo sound from one device
Most speakers work, but some are silentSome speakers are silent
Movies play only in stereo, or Atmos is missingSurround or Dolby Atmos is missing
Sound cuts out, or the receiver shuts offSound cuts out or the receiver turns off

No sound from anything

When every source is silent, work through the settings that affect all inputs, then the speaker wiring.

Check where HDMI sound is going

The “AUDIO.OUT” setting decides whether HDMI sound plays from the receiver’s speakers only, or from the TV speaker as well. It’s only on the receiver’s display panel, not the TV menu.

  1. Press AMP MENU on the remote.
  2. Select “<HDMI>” > “AUDIO.OUT” on the display panel.
  3. Select “AMP” to play HDMI sound from the receiver’s speakers only. “TV+AMP” plays it from the TV speaker and the receiver.
  4. Press AMP MENU to close the menu.

Sony notes that with “TV+AMP,” the sound is limited to what the TV supports. If the TV only handles stereo, the receiver plays stereo too. Turning on “CTRL.HDMI” can also change “AUDIO.OUT” on its own to match the TV’s speaker setting.

STR-DH790 display panel with HDMI then AUDIO.OUT set to AMP
Press AMP MENU, then choose <HDMI> → AUDIO.OUT → AMP. These separately recreated front-display states show the documented sequence; AMP sends HDMI-source audio to the receiver’s speakers. The inset identifies the remote button.

Check the speaker wiring

Warning: turn off and unplug the receiver before you touch speaker wires or terminals.

  1. Check that each speaker wire is connected to the right terminal on the receiver and on the speaker.
  2. Make sure the bare wire ends are tightly twisted and that no stray strand touches another terminal.
  3. Pull each wire gently. Sony’s test tone tip is that wires should not come loose when you pull on them slightly.

Play a test tone

  1. Press AMP MENU.
  2. Select “<LEVEL>” > “T. TONE” on the display panel.
  3. Choose “AUTO”. A tone plays from each speaker in turn, and the display shows which one (FL, CNT, FR, SR, SBR, SBL, SL, HL, HR, SW).
  4. Set “T. TONE” back to “OFF” when you’re done.

If the test tone plays but your sources don’t, the problem is the input or source settings, not the speakers. If no tone plays at all, Sony says the speaker wires may be loose or short-circuited.

STR-DH790 display panel running the automatic test tone on the front left speaker
Under <LEVEL> → T. TONE, AUTO FL identifies the front-left speaker as the test tone cycles. The two recreated display states and original 5.1 room illustration explain that step; available channels depend on your speaker pattern. No tone was played.

No sound from the TV (eARC, ARC, or optical)

When discs and games play but TV apps and channels are silent, work through Sony’s checklist in order.

  1. Make sure the HDMI cable goes from the receiver’s HDMI TV OUT (eARC/ARC) jack to the TV’s HDMI port that supports eARC or ARC.
  2. Turn on the TV’s own HDMI control setting (for Sony TVs, BRAVIA Sync).
  3. Press AMP MENU, select “<HDMI>” > “CTRL.HDMI,” and choose “CTRL ON.”
  4. If your TV has ARC but not eARC, set “<HDMI>” > “EARC” to “OFF.”
  5. Select the receiver’s TV input, and make sure “<INPUT>” > “IN MODE” is set to “AUTO.”
  6. On the TV, set the speaker output to the audio system. On a Sony BRAVIA, Sony calls this setting “Audio System.”
  7. Turn up the receiver’s volume or cancel muting.
STR-DH790 display panel with CTRL.HDMI set to CTRL ON and EARC shown
Set <HDMI> → CTRL.HDMI to CTRL ON, then choose EARC. This recreated sequence shows ON for an eARC example; Sony’s no-TV-sound checklist directs ARC-only TVs to OFF. Each panel is a separate display state, and no setting was changed.

A few more things from Sony’s list:

  • “MUTING” on the display after turning things on. Depending on the order you turn on the TV and receiver, the receiver may start muted. Turn on the TV first, then the receiver.
  • The TV has no System Audio Control. Set “AUDIO.OUT” to “TV+AMP” to hear TV sound from the TV and the receiver, or “AMP” for the receiver only.
  • The TV has no eARC or ARC. Connect the TV’s optical output to the receiver’s OPTICAL TV IN jack, or use an analog audio cable. Sony says TV sound won’t come through an HDMI-only connection to a TV without eARC or ARC.
  • TV sound is quieter than other sources. Raise “<LEVEL>” > “TV.OFFSET”, which goes from “TV 0 dB” to “TV +6 dB.”
  • “EARC” isn’t in the menu. Sony says to update the receiver’s software if the HDMI TV OUT jack is labeled only “ARC” or the EARC item is missing.

Our guide to Control for HDMI and Standby Through on the STR-DH790 explains every HDMI setting on the display panel.

No sound from one device

If a cable box, game console, or disc player is silent while other sources play, the problem is between that device and the receiver.

STR-DH790 display panel with INPUT then IN MODE set to AUTO
For the selected input, open <INPUT> → IN MODE → AUTO. This recreated sequence also lists OPT, COAX and ANALOG as the documented alternatives; availability depends on the input. No real receiver input was changed.
  • You’re on the TV input. Sony says you can’t hear a device connected to the receiver while the TV input is selected. Switch to the device’s own input, such as BD/DVD, GAME, or SAT/CATV.
  • The cable box plugs into the TV. If a cable or satellite box connected to the TV is silent, Sony suggests connecting it to an HDMI input on the receiver instead, then selecting that input.
  • The input mode is wrong. With the device’s input selected, press AMP MENU and go to “<INPUT>” > “IN MODE.” “AUTO” picks HDMI first, then other digital audio, then analog. “OPT,” “COAX,” and “ANALOG” lock the input to one jack.
  • An optical or coaxial jack is assigned elsewhere. Check “<INPUT>” > “A. ASSIGN”. Each digital jack can be assigned to one input, and changing it may change “IN MODE” too.
  • The device’s audio output is off or limited. Some devices need their HDMI or digital audio output turned on in their own settings.
  • The home menu is open. Sony says sound may not play while the home menu is on the TV. Press HOME to close it.
  • The receiver feeds a projector. Sony says sound may not come out when the receiver connects to a projector or similar video device. Set “AUDIO.OUT” to “AMP.”
  • An HDMI-to-DVI adapter is in the chain, or the device doesn’t support HDCP. Sound and picture may be distorted or missing. Use a straight HDMI cable and a device that supports HDCP.

For phones and tablets over Bluetooth, turn up the volume on the device first, then use the receiver’s volume.

Some speakers are silent

Before you rewire, check the sound field. Several of the DH790’s sound fields leave some speakers silent on purpose.

Silent speakersLikely reasonWhat to do
Center and surrounds, with music or Bluetooth2ch Stereo, Direct, Front Surround, or Audio Enhancer keeps stereo sources in the front speakersPick Multi Ch Stereo, Dolby Surround, or Neural-X
Subwoofer2ch Stereo never uses it, and some fields need Size set to SmallChange the sound field or set the speakers to Small
Height speakers, with DTS contentA known exception with a 5.1.2 pattern and some height speaker typesTry Dolby Surround
Rear speakers during dialogueThe source puts little or nothing thereNormal for many scenes. Test with a surround test clip
A speaker that never plays, in any fieldSpeaker pattern, wiring, or levelCheck the pattern and wiring below

To change the sound field, press 2CH/MULTI, MOVIE, or MUSIC until the one you want shows on the display.

Check the speaker pattern, level, and size

  1. Press AMP MENU and select “<SPKR>” > “PATTERN.” Make sure it matches the speakers you actually have, such as “5.1” or “5.1.2.”
  2. Run the test tone (“<LEVEL>” > “T. TONE”) and listen for every speaker.
  3. If a speaker is quiet, raise it in [Speaker Setting] > [Level] from the home menu.
  4. If the surrounds sound thin or distorted, try a different [Size] in [Speaker Setting]. Sony suggests [Small] when sound is distorted or surround effects are lacking.
  5. Run Auto Calibration again from [Easy Setup] if you added, moved, or rewired a speaker.

For a silent subwoofer, make sure it’s turned on and its volume is up. Sony’s list also notes that some sound fields don’t use the sub.

If the left and right sides sound reversed or unbalanced, check that each speaker is wired to the matching terminal, then adjust the levels in [Speaker Setting].

Surround or Dolby Atmos is missing

  • Check the source. The disc or stream has to carry Dolby Digital, DTS, or Atmos. Sony also notes some discs lack Dolby Digital Surround EX information.
  • Check the player. Make sure its digital audio output is on and not set to PCM stereo only.
  • Set “AUDIO.OUT” to “AMP.” Sony lists this for missing Dolby and DTS sound.
  • Use HDMI. Sony says Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos, DTS:X, DSD, and multichannel PCM only play over HDMI.
  • Set the player’s resolution above 720p/1080i for high bitrate audio, as Sony recommends.
  • Pick the right sound field. Sony says Dolby Atmos is decoded as plain Dolby TrueHD or Dolby Digital Plus in any field other than Multi Ch Stereo, A.F.D., or Dolby Surround.

For speaker layout and height settings, see our STR-DH790 Dolby Atmos setup guide.

Sound cuts out or the receiver turns off

What you noticeLikely causeWhat to do
Sound drops for a moment while the sound field changes“S.F. SYNC” is switching fields to match a Sony TV’s Scene Select or Sound ModeSet “<HDMI>” > “S.F. SYNC” to “OFF,” then pick a sound field
Receiver shuts off after about 20 minutes of no signal or useAuto standbySet “<SYSTEM>” > “AUTO.STBY” to “STBY OFF”
Receiver turns off when you turn off the TV“STBY.LINK” follows the TV’s powerSet “<HDMI>” > “STBY.LINK” to “OFF”
Receiver turns off at a set timeSleep timerCancel the sleep timer
“PROTECT” appears, then the receiver shuts offThe protection circuit trippedSee our PROTECT guide below

If you see PROTECT on the display, don’t keep turning the receiver back on. Unplug it, disconnect the speakers, and follow our STR-DH790 PROTECT error guide to find the cause.

If nothing here works

Try the receiver with one simple source and only the two front speakers. If that plays, add speakers and devices back one at a time until the silence returns. That points to the speaker, cable, or setting at fault. Sony’s own last steps for missing rear sound are to replace the speaker wires and try a different pair of speakers.

Warning: a factory reset clears every memorized setting, such as your speaker pattern, calibration results, and input settings.

If settings seem stuck, reset the receiver from its front panel:

  1. Turn off the receiver.
  2. Hold down the power button on the receiver for 5 seconds.
  3. Wait while “CLEARING” flashes. Don’t turn the receiver off until “CLEARED” appears.

Then run Easy Setup again. If you only experimented with sound fields, reset just those instead: with the receiver off, hold MUSIC and press the power button until “S.F. CLEAR” appears.

If the test tone is silent from every speaker with known-good wires and speakers, contact Sony support about the receiver.

Quick answers

Why is there sound from both the TV and my speakers?

“AUDIO.OUT” is set to “TV+AMP.” Press AMP MENU and set “<HDMI>” > “AUDIO.OUT” to “AMP,” or mute the TV.

Can I fix this from the TV menu?

Partly. Inputs, sound fields, and speaker settings are in the home menu on the TV. The HDMI, input mode, and test tone settings are only on the receiver’s display panel, under AMP MENU.

Can I hear a player through the TV with the receiver off?

Yes, with Standby Through. Press AMP MENU, set “<HDMI>” > “CTRL.HDMI” to “CTRL ON,” then set “<HDMI>” > “STBY.THRU” to “AUTO” or “ON.” The TV then plays the HDMI device that was selected before the receiver went into standby.

Sony’s full checklists are on the Help Guide pages No sound, no matter which device is selected and No TV sound is output from the receiver.

More guides for the Sony STR-DH790