Sony STR-DH590 Sound Modes Explained (and Which to Use)

The Sony STR-DH590 has 14 sound fields (Sony’s name for sound modes), grouped under three buttons: 2CH/MULTI, MOVIE, and MUSIC. For most movies, start with HD-D.C.S. For stereo music on a full speaker setup, try PLII Music or Multi Ch Stereo. Use 2ch Stereo or Direct when you want the source played without effects.

Press a button repeatedly to cycle through its group, and watch the receiver’s display for the mode’s short name. Which speakers actually play depends on three things: the sound field, whether the source is stereo or multichannel, and your speaker pattern. That’s why a mode can sound great with a Blu-ray and flat with a phone. The tables below show what each mode does, when to use it, and which speakers it drives.

How to change the sound field

You can switch with the buttons or from the menu on the TV.

With the buttons

  1. Press 2CH/MULTI, MOVIE, or MUSIC on the remote or on the receiver.
  2. Keep pressing the same button until the sound field you want appears on the display panel.

The remote also has a FRONT SURROUND button that jumps straight to Front Surround.

From the home menu

  1. Switch the TV to the receiver’s HDMI input and press HOME.
  2. Select [Sound Effect], then [Sound Field].
Sony STR-DH590 Sound Effect menu with Sound Field highlighted
Recreated menu. Open Sound Effect, then Sound Field, to pick a mode from the TV.
  1. Use the left and right arrows to choose a sound field, then press enter.
STR-DH590 sound fields grouped by button: 2CH/MULTI (2CH ST., MULTI ST., DIRECT), MOVIE (HD-D.C.S., PLII MV, FRT SUR.), MUSIC (ENHANCER, HALL, JAZZ, CONCERT, STADIUM, SPORTS, PLII MS)
Each button cycles through its own group. The names match what the receiver’s display shows.

Every STR-DH590 sound field, explained

Sound field (display)ButtonWhat it doesGood for
2ch Stereo (2CH ST.)2CH/MULTIPlays two channels with no surround effect. Mono and multichannel sources are converted to two channels. Only the front left and right speakers play. The subwoofer is silent.Stereo music on good front speakers, when you don’t want bass sent to the sub
Multi Ch Stereo (MULTI ST.)2CH/MULTIPlays stereo or mono sound from all connected speakers, without adding surround effects.Background music or TV that should fill the room evenly
Direct (DIRECT)2CH/MULTIPlays every audio format without adding any surround effect.Hearing a soundtrack or album as it was encoded
HD-D.C.S. (HD-D.C.S.)MOVIESony’s home theater mode. It’s built from response measurements of a mastering studio, to reproduce the sound the mastering engineer intended.Blu-ray and DVD movies
PLII Movie (PLII MV)MOVIEDolby Pro Logic II Movie decoding. Can play overdubbed or older movies in 5.1-channel format.Movies encoded in Dolby Surround, older films, and stereo TV shows
Front Surround (FRT SUR.)MOVIEUses Sony’s virtual processing to create a surround effect with only two front speakers.Systems with no center or surround speakers
Audio Enhancer (ENHANCER)MUSICMakes sound clearer and more enhanced from portable devices.MP3 and other compressed music, including phones over Bluetooth
Hall (HALL)MUSICSimulates a concert hall.Classical and orchestral music
Jazz (JAZZ)MUSICSimulates a jazz club.Small-group and acoustic recordings
Concert (CONCERT)MUSICSimulates a 300-seat live house.Live-sounding pop and rock
Stadium (STADIUM)MUSICSimulates a large open-air stadium.Big live recordings
Sports (SPORTS)MUSICSimulates the feel of a sports broadcast.Games and sports programs
PLII Music (PLII MS)MUSICDolby Pro Logic II Music decoding.Normal stereo sources such as CDs
Headphone(2ch) (HP 2CH)NoneSelected automatically when headphones are plugged in. Everything plays as two channels. No other sound field can be chosen.Headphone listening

The “What it does” column follows Sony’s descriptions. The “Good for” column combines Sony’s recommendations with plain-language suggestions. Your room and speakers matter, so treat these as starting points, not rules.

Which sound field should you use?

You’re playingTry firstAlso worth trying
A Blu-ray, DVD, or streaming movie with 5.1 soundHD-D.C.S.Direct, to hear the mix untouched
A stereo TV show or older movie on a 5.1 systemPLII MovieMulti Ch Stereo
A CD or lossless stereo musicPLII Music2ch Stereo or Direct, for front-speaker-only listening
Phone music over BluetoothAudio EnhancerMulti Ch Stereo
Anything, with just two speakers (plus a sub)Front Surround2ch Stereo
Sports or a live concert videoSports or ConcertMulti Ch Stereo

Sony’s own rule of thumb is short: pick a sound field labeled Movie for movies and one labeled Music for music.

Which speakers play in each mode

This is where most confusion comes from. With multichannel sources, like Dolby Digital or DTS movies, every sound field except 2ch Stereo can use all your speakers. Front Surround is the other exception. It plays through the front speakers and subwoofer only. With two-channel sources, like most music, Bluetooth, and a lot of TV, the picture changes:

Grid showing which speakers play in each STR-DH590 sound field with a stereo source: front always, center and surrounds in some modes, subwoofer only with an x.1 pattern
With stereo sources, only some modes use the center and surround speakers. Multichannel movies can use every speaker in all modes except 2ch Stereo and Front Surround.
  • Front speakers always play, in every mode.
  • Center and surrounds join in only with Multi Ch Stereo, HD-D.C.S., PLII Movie, PLII Music, and the five venue modes (Hall, Jazz, Concert, Stadium, Sports). Your speaker pattern also has to include them.
  • 2ch Stereo, Direct, Front Surround, and Audio Enhancer keep stereo sources in the front speakers.
  • The subwoofer needs a speaker pattern ending in “.1” in every mode. In Audio Enhancer and the venue modes, the speakers must also be set to [Small]. It never plays in 2ch Stereo, or in Direct with an analog input.

If your bass disappears when you change modes, our STR-DH590 subwoofer fixes walk through the pattern and size settings. If the center or surrounds never play, check the speaker pattern first. It’s set during speaker setup and Auto Calibration, and it’s under “<SPKR>” – “PATTERN” in the AMP MENU.

Tune HD-D.C.S. for your room

HD-D.C.S. has three effect types. You set them from the receiver’s display panel:

  1. Select HD-D.C.S. as the sound field.
  2. Press AMP MENU.
  3. Select “<SURR>” – “EFFECT.”
  4. Choose “DYNAMIC,” “THEATER,” or “STUDIO,” and press enter.
STR-DH590 display showing the HD-D.C.S. effect set to THEATER
Generated two-step display recreation. Select EFFECT, then choose DYNAMIC, THEATER or STUDIO to suit the room; STUDIO is shown.
  • “DYNAMIC” is for rooms that are echoey but don’t feel spacious, where there isn’t much to absorb sound. It emphasizes reflected sound to recreate a large, classic movie theater.
  • “THEATER” is for a general living room. It reproduces the reverb of a movie theater (Sony specifies a dubbing theater). Sony calls it the best fit for Blu-ray movies when you want a theater atmosphere.
  • “STUDIO” is for a living room with suitable sound equipment. It reproduces the sound of a theatrical mix remixed for Blu-ray at home volume levels. Reflections and reverb are kept to a minimum, so dialogue and surround effects come through vividly.

The effect type only applies when HD-D.C.S. is selected, and not while headphones are connected.

Direct, 2ch Stereo, and Pure Direct: what’s the difference?

These three sound similar but do different jobs.

  • 2ch Stereo folds everything down to two channels and plays only the front pair. Even a 5.1 movie plays from two speakers, and the subwoofer is silent.
  • Direct plays the source without effects but keeps its channels. A 5.1 movie still uses all your speakers. With an analog input, Direct skips the subwoofer, and the receiver doesn’t apply Calibration Type or the Bass and Treble settings.
  • Pure Direct isn’t a sound field. It’s a separate switch that works alongside one. Turn it on with the PURE DIRECT button, or through [Sound Effect] – [Pure Direct] in the home menu. The display panel turns off and the PURE DIRECT indicator lights. While it’s on, Calibration Type, Night Mode, Bass, Treble, and “D. RANGE” don’t work.
STR-DH590 front panel with the display off and the PURE DIRECT light on
Generated illustrative recreation. With Pure Direct on, the display turns off and the PURE DIRECT light comes on.

Pure Direct turns itself off if you change the sound field or adjust Bass, Treble, Night Mode, or “D. RANGE.” If the receiver’s display seems dead, check for the PURE DIRECT light before assuming something is wrong.

Settings that work with any sound field

Night Mode for late-night movies

Night Mode keeps dialogue clear at low volume. It raises the bass, treble, and effect levels and sets “D. RANGE” to “COMP. ON” automatically. Press NIGHT MODE on the receiver or remote, or go to [Sound Effect] – [Night Mode] and select [On]. It doesn’t work with Pure Direct on, with headphones connected, or in Direct with an analog input.

“D. RANGE” to tame loud scenes

Dynamic range compression narrows the gap between quiet and loud sounds. Set it under AMP MENU – “<AUDIO>” – “D. RANGE.” “COMP. ON” compresses as the recording engineer intended, and “COMP. AUTO” compresses only when the source is flagged for it. It only works with Dolby Digital and Dolby TrueHD sources.

Bass and Treble

Go to [Sound Effect] in the home menu and choose [Bass] or [Treble], then use the up and down arrows to set the level. These adjust the front speakers. The frequencies are fixed, so you can only change the level. Like Night Mode, they’re off in Pure Direct and in Direct with an analog input.

When sound fields don’t behave

PLII Movie and PLII Music are missing or do nothing

Sony says they don’t work when the speaker pattern is “2.0” or “2.1.” With two front speakers, use Front Surround instead.

A Dolby or DTS movie plays in stereo

  • Make sure the disc or stream actually has Dolby Digital or DTS audio, and that the player’s digital audio output is turned on.
  • Press AMP MENU and set “<HDMI>” – “AUDIO.OUT” to “AMP.” With “TV+AMP,” sound is limited to what the TV can handle, which can mean stereo.
STR-DH590 display showing HDMI AUDIO.OUT set to AMP
Generated two-step display recreation. Select AUDIO.OUT, then AMP, so the receiver decodes Dolby and DTS.
  • Dolby TrueHD, DTS-HD Master Audio, DSD, and multichannel PCM only play over an HDMI connection, not optical or coaxial.
  • Check that you aren’t in 2ch Stereo.

The sound field changes by itself

That’s “S.F. SYNC” at work with a Sony TV. It picks a sound field based on the TV’s Scene Select or Sound Mode, or the program’s genre. For example, Cinema selects HD-D.C.S., Sports selects Sports, and Music selects Concert. To choose sound fields yourself, press AMP MENU and set “<HDMI>” – “S.F. SYNC” to “OFF.” With it off, you can set a sound field for each input.

You can’t select any sound field

Headphones are plugged into the PHONES jack. The receiver locks to Headphone(2ch) until you unplug them.

Everything sounds wrong after experimenting

Reset just the sound fields. Turn the receiver off, hold MUSIC on the receiver, and press the power button. “S.F. CLEAR” appears, and all sound fields return to their defaults. Your speaker setup and other settings stay put. This is lighter than a full factory reset of the STR-DH590, which erases everything.

Quick answers

Does the STR-DH590 have a Dolby Atmos mode?

No. None of its 14 sound fields is an Atmos or DTS:X mode, and it has no height-speaker outputs in its speaker patterns. If you want Atmos, that’s a feature of the step-up model, covered in our STR-DH790 Dolby Atmos setup guide.

Which mode is the “purest”?

Direct, with Pure Direct turned on. That combination adds no surround effect and turns off the tone and dynamic range processing. For a stereo source, 2ch Stereo is the choice that keeps sound in the front speakers only.

Sony’s Help Guide has the full details on its pages about selectable sound fields and their effects and which speakers each sound field uses.

More guides for the Sony STR-DH590