How to Fix No Sound on a Sony STR-DH590

When a Sony STR-DH590 plays no sound, start with four quick checks. Make sure the display doesn’t say MUTING or show the volume at VOL MIN, unplug any headphones from the PHONES jack, press SPEAKERS on the receiver until it shows a setting other than OFF, and select the input your device is actually connected to. Those fix most cases. If you still hear nothing, use the section below that matches your symptom.

This guide covers silence from every source, from the TV, from one HDMI device, and from single speakers. A silent subwoofer has its own guide, linked below.

Match your symptom

What happensGo to
No sound from anything, or very quiet soundNo sound from any source
Players work, but TV apps and channels are silentNo sound from the TV
One HDMI device is silent, others workNo sound from one device
Center or surround speakers are silentOne or more speakers are silent
The receiver keeps turning offThe receiver shuts off by itself

No sound from any source

Work through these in order. Sony’s help guide lists the same checks for when there’s no sound or very low sound whatever device you pick.

  1. Check the cables. Make sure every cable is pushed fully into its jack on the receiver, the speakers, and your devices.
  2. Check the volume. Turn MASTER VOLUME up. If the display shows VOL MIN, the volume is all the way down.
  3. Cancel muting. Press the muting button on the remote, or turn the volume up.
  4. Turn the speakers on. Press SPEAKERS on the receiver repeatedly until the display shows a setting other than OFF.
  5. Unplug headphones. Sony says to make sure nothing is connected to the receiver’s headphone jack.
  6. Select the right input. Press the input button on the remote, or turn INPUT SELECTOR on the receiver, until you reach the input your device is connected to.
STR-DH590 front panel with SPEAKERS, PHONES, INPUT SELECTOR and MASTER VOLUME highlighted
Generated illustrative recreation of the STR-DH590 controls used for the first sound checks. The SPEAKERS button, empty PHONES jack, INPUT SELECTOR and MASTER VOLUME are marked. BD/DVD is an example input; unrelated control labels are omitted.

Then test the speakers themselves. Press AMP MENU, select <LEVEL> > T. TONE, and choose the AUTO setting. A test tone plays from each speaker in turn. Set it back to OFF when you’re done. If a speaker stays silent during the tone, Sony says its wire may be loose or shorted. Unplug the receiver, check that the wire is held firmly at both ends, and test again.

STR-DH590 front display showing LEVEL, T. TONE, and AUTO FL for the speaker test tone
AMP MENU → <LEVEL> → T. TONE → AUTO FL starts the documented cycling tone. These recreated display states show the front-left step; a full 5.1 pattern then includes CNT, FR, SR, SL and SW. No actual tone was played.

If the display panel is dark: Two things can blank it while the receiver is on. Pure Direct turns the display off, and the PURE DIRECT indicator lights up. Press PURE DIRECT to turn it off. The DIMMER button also cycles through BRIGHT, DARK, and no display. A dark display doesn’t mean there’s no sound, but it can make the receiver look switched off.

No sound from the TV

TV apps and channels reach the receiver over HDMI ARC or an optical cable. Players connected to the receiver’s own HDMI IN jacks don’t use that path, so a working Blu-ray player with a silent TV points to the TV connection.

  1. Switch the receiver to its TV input.
  2. Check that the HDMI cable goes from the receiver’s HDMI TV OUT jack to the TV’s HDMI input marked ARC.
  3. Press AMP MENU and make sure <HDMI> > CTRL.HDMI is set to CTRL ON. Turn on HDMI control in the TV too.
  4. With the TV input selected, set <INPUT> > IN MODE to AUTO.
STR-DH590 front display showing IN MODE set to AUTO on the TV input
With TV selected, use AMP MENU → <INPUT> → IN MODE → AUTO. These recreated display states and the remote-button detail illustrate the sequence; no receiver input or setting was changed.
  1. Set the TV’s speaker setting to the audio system. On a Sony BRAVIA, Sony calls it Audio System.
  2. If MUTING shows on the receiver, turn on the TV first and then the receiver. Sony says the power-on order can cause this.

If your TV doesn’t support System Audio Control, press AMP MENU and set <HDMI> > AUDIO.OUT yourself. Choose AMP for the receiver’s speakers only, or TV+AMP for the TV speaker and the receiver together. If your TV has no ARC, Sony says to use an optical or analog audio cable, since an HDMI connection alone gives no TV sound.

Our STR-DH590 HDMI ARC setup guide covers the full hookup and the optical alternative.

No sound from one device

If one player or box is silent while others work, the problem is with that device’s connection or settings.

  • Use the device’s input, not TV. Sony says you can’t hear a device connected to the receiver while the TV input is selected. Switch to the HDMI input the device is plugged into.
  • Exit the home menu. Sony notes the receiver may not output sound while its home menu is showing on the TV. Press HOME to close it.
  • Check IN MODE. Press AMP MENU and look at <INPUT> > IN MODE. AUTO gives priority to digital signals, with HDMI first. If you connected a device by optical, coaxial, or analog, make sure the mode isn’t locked to a different jack.
  • Check A. ASSIGN. If you reassigned an optical or coaxial jack with <INPUT> > A. ASSIGN, make sure the jack isn’t assigned to another input. Assigning a jack can also change IN MODE automatically.
  • Check the device’s audio output. Some players and consoles need their HDMI or digital audio output turned on. Sony says a device can also limit the audio formats it sends over HDMI.
  • Swap the HDMI cable. Sony recommends a High Speed HDMI Cable with Ethernet. For 4K/60p 4:4:4, 4:2:2, and 4K/60p 4:2:0 10 bit, it requires a Premium High Speed HDMI Cable with Ethernet that supports 18 Gbps.
  • Check copy protection. If a connected device doesn’t support HDCP, Sony says the picture or sound from HDMI TV OUT may be distorted or missing.
  • Projector users. If the receiver feeds a projector, Sony says sound may not play. Set <HDMI> > AUDIO.OUT to AMP.

A cable or satellite box plugged into the TV may not pass its sound back. Sony’s fix is to connect the box to an HDMI input on the receiver and switch to that input. If you also have no picture, see our guide to fixing no picture or no signal through the STR-DH590.

Movie soundtracks play in stereo or not at all

  • Check that the disc or stream is actually in Dolby Digital or DTS.
  • Set <HDMI> > AUDIO.OUT to AMP. With TV+AMP, Sony says the formats and channels are limited to what the TV supports. A stereo-only TV means stereo from the receiver too.
  • Dolby TrueHD, DTS-HD Master Audio, DSD, and multichannel PCM only work over HDMI. For high bitrate audio, Sony says to set the player’s video resolution above 720p/1080i.

One or more speakers are silent

  1. Press AMP MENU and check <SPKR> > PATTERN. It needs to match the speakers you actually connected. A 2.1 or 2.0 pattern leaves the center and surrounds silent.
STR-DH590 front display showing the speaker PATTERN set to 5.1
Choose <SPKR> → PATTERN to match the speakers actually connected. These recreated display states use a 5.1 example—five speakers and a subwoofer. No speaker pattern was applied to a real receiver.
  1. Run the test tone from <LEVEL> > T. TONE to see which speakers play.
  2. Check the sound field. 2ch Stereo only uses the front speakers, and so does Front Surround. Sony’s chart shows the center and surrounds stay silent in those modes. Pick Multi Ch Stereo, a MOVIE mode, or Direct with a multichannel source.
  3. Remember that surround speakers often go quiet during dialogue. Sony notes that most of the sound can come from the center speaker until there’s background sound.
  4. If the levels are off, rerun Auto Calibration from [Easy Setup] in the home menu, or adjust [Speaker Setting] > [Level].

Sony’s help guide has a full chart of which speakers each sound field uses.

The subwoofer is silent

Sony says to make sure the subwoofer is turned on and its volume is up. In 2ch Stereo, the subwoofer gets no sound at all. With the music sound fields, it only plays if some speakers are set to [Small] or the source has an LFE channel. Our guide to fixing no sound from the STR-DH590 subwoofer covers every cause.

The receiver shuts off by itself

An automatic shutdown can look like a loss of sound. Sony lists three causes:

  • Auto standby. With <SYSTEM> > AUTO.STBY on STBY ON, the receiver turns off after about 20 minutes with no use or no signal. Set it to STBY OFF.
  • Sleep timer. The timer may be running.
  • PROTECT. If PROTECT flashes on the display before it turns off, the protection circuit tripped. Our STR-DH590 reset and PROTECT guide lists Sony’s checks.

Bluetooth is connected but silent

Sony says to turn up the volume on your phone or tablet first, then use the receiver’s volume. Also make sure the receiver is on its BT input. If the device won’t connect at all, pair it again. Press BLUETOOTH PAIRING on the remote and select STR-DH590 on the device within five minutes.

Still nothing?

Sony’s support article suggests one more round of checks before you assume a fault:

  • Try different cables, and try each HDMI input on the receiver.
  • Connect the source directly to the TV. If its sound is fine there but not through the receiver, the receiver may need service.
  • Reset the receiver to its factory settings. Turn it off, then hold the power button on the receiver for 5 seconds until CLEARING flashes.

Warning: A factory reset clears all your settings, including your speaker pattern and calibration. Don’t turn the receiver off until CLEARED appears. Run Easy Setup again afterward.

Quick answers

Why is there sound from my TV speaker but not my receiver?

The TV is sending sound to its own speakers. Set the TV’s speaker output to the audio system and check that CTRL.HDMI is CTRL ON. If your TV lacks System Audio Control, set AUDIO.OUT to AMP.

Why does the sound cut out when I change scenes or shows?

Check <HDMI> > S.F. SYNC. When it’s on, the sound field follows the TV’s scene setting, and Sony says the switch can interrupt the sound. Turn it off and pick a sound field yourself.

Sony’s full checklists are on the STR-DH590 Help Guide pages for no sound from any device and no sound from a specific device.

More guides for the Sony STR-DH590