Denon AVR-S570BT Sound Modes Explained (and Which to Use)

To change the sound mode on the Denon AVR-S570BT, press SOUND MODE ◀ or ▶ on the remote (or the SOUND MODE buttons on the front panel) until the mode you want shows on the display. The modes you can pick depend on what you’re playing, so a stereo source and a Dolby Digital movie show different lists.

For most people the choice is simple. Let a 5.1 movie play in its own Dolby or DTS mode. Use Dolby PL II or DTS Neo:6 to spread stereo TV shows and music across all five speakers. Use Stereo or Direct when you want music to sound the way it was mixed. The S570BT is a 5.2-channel receiver, and Denon lists no Dolby Atmos, Dolby Surround, or DTS:X modes for it.

Every S570BT sound mode at a glance

Denon groups the modes like this. The descriptions are based on Denon’s own wording in the AVR-S570BT manual.

ModeGroupWhat it does
Dolby PL IIDolbyTurns a 2-channel source into 5.1-channel surround
Dolby DigitalDolbyPlays sources recorded in Dolby Digital
Dolby Digital PlusDolbyPlays sources recorded in Dolby Digital Plus
Dolby TrueHDDolbyPlays sources recorded in Dolby TrueHD (lossless)
DTS Neo:6DTSTurns a 2-channel source into 5.1-channel surround
DTS SurroundDTSPlays sources recorded in DTS
DTS-HDDTSPlays sources recorded in DTS-HD
Multi Ch InPCMPlays multichannel PCM sources
Multi Ch StereoDenon originalPlays stereo sound from all speakers
VirtualDenon originalCreates a wider surround effect from just the front left and right speakers, or from stereo headphones
StereoStereoFront left and right speakers plus the subwoofer, with no surround processing
DirectDirectPlays audio as recorded in the source
Pure DirectDirectLike Direct, and also turns off the display circuit for even higher sound quality

How to change the sound mode

  1. Start playing something. The list of modes depends on the incoming signal, so it’s easiest to choose while content is playing.
  2. Press SOUND MODE ◀ or ▶ on the remote to move through the available modes. The SOUND MODE buttons on the front panel do the same thing.
  3. Watch the front display, which shows the current sound mode name.
Denon AVR-S570BT front display showing the sound mode name with the remote's SOUND MODE buttons
Generated illustrative recreation. Press SOUND MODE ◀ or ▶ and watch the display until your mode appears.
  1. Stop when you reach the mode you want.

Three behaviors surprise people, and all of them are by design:

  • Each input remembers its own mode. Denon’s Personal Memory Plus saves the last sound mode for each input source. Picking Stereo on Bluetooth won’t change what you hear from the TV Audio input.
  • The receiver can switch modes for you. If new content doesn’t support the mode you chose, the receiver picks the most suitable one on its own. For example, a switch from a stereo show to a Dolby Digital movie can change the mode.
  • Some modes only show up for some signals. Dolby TrueHD only appears when a TrueHD signal comes in, and the upmixers are meant for 2-channel sources.

What each group is for

Four top-view diagrams of a 5.1 layout showing which speakers play in Stereo or Virtual, Multi Ch Stereo, Dolby PL II or DTS Neo:6, and Dolby, DTS, or PCM surround modes
Stereo and Virtual leave the center and surrounds silent. That’s by design, not a wiring fault.

Dolby, DTS, and Multi Ch In: play it as it was mixed

When a movie, game, or streaming show sends real surround sound, these modes play each channel through its matching speaker. Dolby TrueHD and DTS-HD are the lossless formats found on many Blu-ray discs. Multi Ch In handles multichannel PCM, the uncompressed surround format.

Some sources carry more channels than the S570BT’s 5.1 speakers. Denon’s manual notes, for example, that Dolby Digital Plus can hold up to 7.1 channels. The receiver’s downmix function fits extra channels into the speakers you actually have. For surround sources, these are usually the right modes to leave alone.

Dolby PL II and DTS Neo:6: stereo spread to five speakers

These are upmixers. They take a 2-channel source, such as a TV broadcast, a phone over Bluetooth, or a CD, and decode it into 5.1 surround. Each one has sub-modes you choose in SETUP > Audio > Surround Parameter > Mode:

  • Dolby PL II: Movie, Music, Game, or Pro Logic (the older Dolby Pro Logic playback)
  • DTS Neo:6: Cinema or Music
Denon AVR-S570BT Surround Parameter Mode setting with Dolby PL II Movie selected
Recreated menu. Choose the Dolby PL II or DTS Neo:6 sub-mode under Surround Parameter > Mode.

The Music sub-modes add their own adjustments. Dolby PL II Music unlocks Panorama, Dimension, and Center Width. DTS Neo:6 Music unlocks Center Image, which moves some of the center channel’s dialogue out to the front left and right speakers.

You can’t pick either upmixer if Speaker Layout has both Center and Surround set to No, or if headphones are plugged in.

Multi Ch Stereo: party mode

Multi Ch Stereo plays stereo from every speaker. It doesn’t try to steer sounds to particular speakers like the upmixers do. It’s good for background music at a party. It’s not what you want for movies, because it doesn’t keep dialogue in the center.

Stereo and Virtual: front speakers only

Stereo uses the front left and right speakers, plus the subwoofer if you have one. If a multichannel signal comes in, Stereo mixes it down to 2 channels. Virtual is for setups with only front speakers, or for listening on stereo headphones. It tries to make the sound seem wider than two speakers.

In both modes, the center and surround speakers stay silent. That’s normal, not a fault.

Direct and Pure Direct: the least processing

Both play the source as it was recorded. In these two modes you can’t use the Tone controls, Restorer, or Room EQ. Pure Direct goes further. It turns off the receiver’s display about 5 seconds after you pick it. Denon switches off the display circuit to improve sound quality. The dark display is expected. It doesn’t mean the receiver is off.

If you tuned your room with Auto Setup, remember that Direct and Pure Direct skip Room EQ. Our S570BT speaker setup guide explains what Room EQ does.

Which mode to use

These are starting points based on how Denon describes each mode. Your room and speakers matter, so try a couple and trust your ears.

What you’re playingTry this
Blu-ray, streaming, or a console sending 5.1The mode the receiver picks (Dolby, DTS, or Multi Ch In)
Stereo TV shows, news, sportsDolby PL II (Movie) or DTS Neo:6 (Cinema)
Stereo gamesDolby PL II (Game)
Music, focused listeningStereo, Direct, or Pure Direct
Music, filling the roomDolby PL II (Music), DTS Neo:6 (Music), or Multi Ch Stereo
Only two speakers, or headphonesStereo or Virtual

Settings that fine-tune the sound

Surround Parameter

Go to SETUP > Audio > Surround Parameter. The items you see depend on the incoming signal and the current mode, and the receiver saves these settings separately for each sound mode.

SettingRange (default)Notes
ModePL II: Movie, Music, Game, Pro Logic. Neo:6: Cinema, MusicSub-mode of the upmixer
Dynamic CompressionAuto, Low, Medium, High, Off (Off)Makes loud and quiet parts closer in volume. Auto only works with Dolby TrueHD.
Low Frequency Effects–10 to 0 dB (0 dB)Denon suggests 0 dB for Dolby and DTS movies and –10 dB for DTS music.
Center Image0.0 to 1.0 (0.3)DTS Neo:6 Music only
PanoramaOn, Off (Off)Dolby PL II Music only. Extends the front sound toward the rear.
Dimension0 to 6 (3)Dolby PL II Music only. Moves the sound toward the front or rear.
Center Width0 to 7 (3)Dolby PL II Music only. Spreads center dialogue toward the left and right.
SubwooferOn, Off (On)Direct and Stereo only, when Subwoofer Output is set to LFE+Main

Choose Set Defaults at the bottom of the list to put all the surround parameters back.

Quick adjustments from the OPTION menu

Press OPTION on the remote for settings you’ll change more often:

  • Tone: Bass and Treble from –6 dB to +6 dB. It’s not available in Direct or Pure Direct, or when HDMI Audio Out is set to TV.
  • Night Mode: reduces the gap between loud and soft sounds for late-night viewing. It works only with Dolby Digital signals, and its Auto setting needs Dolby TrueHD.
Denon AVR-S570BT OPTION menu showing the Tone and Night Mode items
Recreated menu. Press OPTION for quick Tone and Night Mode changes without opening SETUP.

Restorer for compressed music

SETUP > Audio > Restorer tries to rebuild detail that formats like MP3 throw away and adds some bass. It’s Off by default, it works on analog and 44.1 or 48 kHz PCM signals, and it isn’t available in Direct or Pure Direct. The receiver saves the setting separately for each input.

When a sound mode doesn’t act the way you expect

Dolby PL II or DTS Neo:6 isn’t in the list

Check SETUP > Speakers > Manual Setup > Speaker Layout. If Center and Surround are both set to No, the upmixers are hidden. Also unplug any headphones from the PHONES jack.

The center or surround speakers are silent

You’re probably in Stereo or Virtual, which only use the front speakers and subwoofer. Press SOUND MODE until you reach a surround mode. If a speaker is still silent in Multi Ch Stereo, check its wiring and Speaker Layout. Our S570BT no-sound guide covers that step by step.

The subwoofer goes quiet in Stereo or Direct

Denon’s tip for making the subwoofer always play is to go to SETUP > Speakers > Advanced Setup and set Subwoofer Output to LFE+Main. With that set, the Subwoofer item in Surround Parameter (On by default) controls whether the sub plays in Direct and Stereo, so make sure it’s On. For the cabling side, see our guide on how to connect a subwoofer to an AV receiver.

The mode keeps changing on its own

Either the input changed (each input keeps its own mode) or the content changed to a format your chosen mode doesn’t support, so the receiver picked a new one. Choose your mode again after the new content starts.

The display went dark

You’re in Pure Direct, which turns off the display after about 5 seconds. Switch to any other mode to bring it back.

Denon’s mode descriptions are on the Auto surround playback page of the AVR-S570BT manual, and the adjustments are on the Surround Parameter page.

More guides for the Denon AVR-S570BT